CLIQUER ICI POUR VOIR DES PHOTOS DE
SURUGA
Materials
Skin |
1 sheet of Washi or similar 62cm by 46cm |
Frame - bamboo |
1 off 2mm by 5mm 47cm long (top spar)
1 off 2mm by 5mm 62cm long (spine)
2 off 2mm by 4mm 73cm long (diagonal spars)
|
Bridles - Linen, cotton |
2 metre long for bridle
1 metre long for bow line |
Glue |
PVA (white glue) Aquadere or similar |
Paint and Indian ink for outline Water based
dyes or food colouring etc for pastels and shading. |
|
|
1. Drawing the outline
Fold the washi in half so the smooth side is in. If using a substitute
material the smooth side will be the side that you later paint.
Draw the lines as shown for the kite outline on one half of the kite.
Draw a 1 cm margin (hem allowance) around the kite sides and bottom
outline and a 2 cm margin at the top.
By using a bamboo skewer (satay stick) or a pin etc make a small hole at
points A, B and C. This will ensure that your kite is symmetrical. |
Unfold the paper and draw connecting lines to points Bī and b. Draw
the margin (hem allowance) around the outline on this side, 1 cm for the
sides and bottom and 2cm at the top.
Cut off the shaded sections X and Y.
|
|
|
Glue the pieces X and Y on to the opposite sides of the
kite as shown overlapping the 1cm hem.
Place the washi smooth side down and fold/crease around the kite outline.
You should now have a kite skin with a crease line that distinguishes
kite and hem allowance. |
2.
Now Paint your kite
3. Framing
Make sure the skin is dry.
Place the kite skin face down and apply a thin coat of glue to the hem
allowance. Fold at the crease mark of the kite outline and with the
exception of the top hem glue all other the hems down on the back side
of the kite.
With the exception of the top 2cms apply a thin but thorough coating of
glue to one side of the vertical bamboo spar and place in position so
that the bamboo extends approximately 5mm above the top of the kite.
Apply a thin but thorough coating of glue to one side of the bamboo
diagonal spars and place in position as shown in the diagram. Repeat for
second cross spar.
Glue the top horizontal spar so that the spar edge sits on the kite
outline.
Cut a nick into the washi around the vertical spar and glue and fold the
2cm hem down over the top of the bamboo.Glue small pieces of Washi as
reinforcing over the corners and spar intersecting points on the back of
the kite.
|
|
|
4. Bridling
Make a small hole with the skewer or pin etc at point L just below the
join of the vertical and horizontal spars. Feed from the front of the
kite one the ends of one of the 3 metre bridle line through this hole.
Loop the end back through the hole several times to ensure the bridle
line is lashed around both spars. Then knot the line.
Mark a point at the intersection of the centre vertical spar and a line
joining the two side points of the kite, M on the diagram. Make a small
hole either side of the vertical spar. Feed from the front of the kite
the other end of the 2 metre bridle line through this hole. Loop the end
back through the hole several times to ensure the bridle line is lashed
around the spar. Once again knot the line.
Mark a point where the spine and diagonals cross on the front of kite
skin. Take the steel washer and feed the bridle loop through it. Then
slide the washer along the lines until it comes to rest over the mark
you have just made.
Hold this spot and at the same time tie the end of the line with an
overhand knot. This will give a bridle with the top leg being shorter
than the bottom.
|
Bowline
Tie the 1 metre line across the back of the kite from one end of a spar
to its opposite side ensuring little or no slack.
Flying
The amount of bow can be adjusted for wind conditions by flexing the
kite towards you and wrapping the slack line around the spar. For
average winds two wraps of the line are recommended.
Attach a flying line to the overhand knot and fly. For displaying your
new kite on your wall or transporting, release the bow.
|
|
|